1/3/2024 0 Comments Ladder stands plans![]() ![]() These step-by-step free plans on the DIY deer stand will make it easy to hunt fast without fearing wild animals attacking you. You can also make a stylish four-legged cupcake stand like YouTuber Michelle from the Around the House channel did.If you are a hunter, you must build a hunting spot for more ease and have a perfect sight of your hunt. If you cut the pieces just right, you can make a collapsible cupcake shelf that you can assemble anytime there’s a party. Jessica’s extensive tutorial covers everything you need to know about making a cupcake stand – and you can make your own variation with the knowledge. The coating also protects it from moisture when you clean it. Spray at least two coats of polyurethane onto the cupcake stand to make it resistant to weathering and abrasion. She does two coats of the stain in the front, and the dark stain goes well with almost every party theme. What is the best stain to use for the cupcake stand? Skip through the video below using the time markers above to find all the juicy parts of making your own cupcake stand come to life for your own upcoming birthday party or celebratory events for years to come. Jessica demonstrates the final step and finishes her rustic cupcake ladder stand tutorial with some sweet pictures of her family enjoying a party. Make sure the shelves are centered and use four screws to connect each shelf to the frame.įinally, stain your stand using a brush, and wipe off any excess using the towel – your cupcake ladder is ready for a party! The frames must be 16 inches apart – this gives the 20″ shelves a nice, spacey feel. She uses two screws to connect the legs to the frames, and also uses wood glue for a firmer hold. Jessica’s process is simple: she pre-drills a hole, countersinks it, then drills the screw in. Skip ahead to 3:43 on the video below to view this step. 04 Sand All Piecesįirst, use 120-grit sandpaper and sand all the pieces of wood, then sand it again using 300-grit sandpaper. Jessica makes the legs for the frame at 3:21 on her video below. In the video, Jessica uses a leftover piece of 2’x4′ board, places it right next to the frame, and marks the angle needed to make the leg seamless.Īs long as you made the same measurements and cuts, the angle will be a perfect 30°.Īfter you mark the angle, saw it off, and saw the single board into two to make the two legs. Skip forward to 2:50 to see Jessica demonstrate this step. Grab the pieces of pallet wood and cut out 20-inch length from each board. Sawing the frame should be easy – just follow the markings. Watch Jessica make her precise markings from the 0:13 mark. She also makes a 90° connecting the first marking to the base of the frame – sawing this off will make the shelf neater. The pallet board Jessica uses for the shelves are shorter than the board she uses for the frame, so she marks the width for sawing off the extra lip of the board. Erase the 90° line, so you don’t get confused – the last 50° angle line will hold the fourth and topmost shelf. Make a 90° line at the end of the third triangle, and mark the final 50° angle from there. You must make a total of three triangles, which will hold three shelves. Use the end of the triangle as the starting point to mark the next triangle with the same dimensions. Use your carpenter ruler to draw a triangle two inches deep and four inches long from the first marking on the board’s edge. In the video, Jessica also marks where the front of the frame is to ensure she doesn’t make any errors when she begins to saw. Make a tiny marking 2 ½ inches above the straight line you marked – this is where the first shelf will start. Then, use a protractor to mark a 50° angle – this is the angle at which the shelves will “rise.” Grab the 20″ long 2’x4′ board and use a triangle to make a 90° straight line near the bottom – this is the base of your frame. But you only need to mark the frames correctly once, and the rest will fall in place. This is often the most challenging step since you need to be very precise. Grab the supplies, and let’s get right to it! Steps to Make a Rustic Cupcake Ladder Stand 01 Make Markings If you’ve done some woodwork before, you likely have most of these supplies handy. Other needed supplies include: Towel, Brush, Stain, Sanding Sealer, and Wood Glue Drill with pre-drill bit, countersink bit, and screwdriver bit.Wood Shelves: Four 3/4″ x 1/2″ pallet wood 20″ in length.Wood Legs: One 2’x4′ about 14″ in length.Wood Frame: Two 2’x4′ about 18″-20″ in length. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |